|
|
Racing Beat Header for 90-93 Miata
|
|
BackOrder - Email us for Pre-Sale
Item Number: RB-56005
Manufacturer: Racing Beat
|
 |
Exhaust Header
1990-1993 Miata |
| Miata Header for 90-93 Miata * |
|
Racing Beat Miata Headers for the 1990-1993 Miata (manual transmission only) are the result of exhaustive research and engineering efforts, utilizing both chassis dynamometer and road testing. Racing Beat Miata headers incorporate a tuned 4-to-1 design configuration to optimize exhaust gas scavenging characteristics and power output, while improving both the exhaust note and retaining the factory catalytic converter. Hundreds of development hours and over 200 on-chassis dyno runs were undertaken in the refinement of their Miata headers. The Racing Beat Miata header has been design-tuned to provide measurable horsepower and torque improvements throughout he entire RPM range.
|
 |
| Manufactured entirely from 304-stainless steel for superior durability, this 4:1 Miata header will offer years of enthusiastic performance driving. Racing Beat's exclusive cast stainless steel engine-to-header flange features specially designed exhaust ports which transition smoothly to the primary tubing. For the 1.6 liter Miata engine our header utilizes large diameter 1.5" OD tubing for the primary tubing, and then collects into 2.0" OD secondary tubing. All emissions control devices are retained. Each Miata header kit comes complete with installation instructions and replacement rear gasket. If needed, an Exhaust manifold gasket (header-to-engine) can be ordered separately. |
 |
Header Development
|
During the summer of 2002 Racing Beat undertook a significant project to upgrade the Racing Beat Miata header line. The scope of the project was to produce a 4-1 (four-into-one) type header for both the 1.6 & 1.8 liter Miatas and compare them against the power characteristics of our then current 4-2-1 (Tri-Y) type headers. These new prototype headers featured a new engine-to-header flange, collector, and outlet flange. They also took the opportunity to change construction materials from mild-steel to 304-stainless steel.
With the new 4:1 header project, Racing Beat's initial performance objective was to retain the mid-range performance (3,000-5,000 RPM) of the then current 4-2-1 (Tri-Y) header, and improve the top-end performance (5,000-7,000 RPM) normally associated with the 4:1 type header. Under the guidance of Jim Mederer, Racing Beat's co-founder and chief engineer, initial testing on this project took place almost entirely on the chassis dyno. A rather strange looking test header was configured that allowed them to actually change the primary and/or secondary lengths while the car was strapped to the dyno. This entire assembly was suspended over the car by a specially built frame.
|
 |
 |
Over 200 on-chassis dyno runs allowed Racing Beat to determine the optimum tubing diameters and lengths for both the primary and secondary tubes. They also took the opportunity to experiment with various engine-to-header flange porting configurations and collector designs. This development allowed Racing Beat to fine-tune the performance of this new header to achieve the performance requirements.
|
After repeated test sessions, they finally found the optimal combination that allowed them to achieve their target goal. The test results showed that the top end power of our 4:1 header had improved and the mid-range power was retained. Click here to view an article on the development of our Miata headers and dyno results.
Once the cast stainless steel engine-to-header flange the flange was completed, the prototype was assembled and the 1990 Miata headed back out to the chassis dyno for final confirmation testing. Click here to view the dyno results for the 1600cc header.
NOTE: Header shown is for the 2001-05 Miata. Review the following Miata Header Identification Chart for the specific differences between the various Miata header configurations.
|
 |
| * Legal in California only for racing vehicles, which may never be used upon a highway. |
|
|
|
|
|
Price: From $21.00 to $139.00
|
|
|
The Track Dog Racing™ exclusive heat shield was designed to help keep your under hood temperatures in check. A must for aftermarket headers, supercharger applications or those running an open element intake near the header.
|
|
|
|
|
|
Price: From $229.00 to $309.00
|
|
|
We have found a high quality replacement catalyst for your Miata. MagnaFlow specializes in superior catalytic converter and exhaust technology and has spent the past 30+ years earning its reputation as a global market leader.
|
|
|
|
|
|
|
|
|
|
A Power Pulse Miata Connecting Pipe is required with the Racing Beat single or dual outlet Power Pulse muffler assemblies on all 1990-1997 Miatas for proper fitment.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Exhaust leaks can decrease performance or even be deadly by directing harmful carbon monoxide into the interior. Genuine Mazda gaskets are guaranteed to fit and seal when used in the proper application. Fits both OEM and Racing Beat aftermarket exhaust.
|
|
|
|
|
|
Price: From $20.00 to $38.00
|
|
|
When the air/fuel combination is burned up inside your engine, the residual gas will be sent away through the exhaust manifold or header. An exhaust manifold gasket is built to keep the toxic gasses from seeping away from the engine.
|
|
|
Product Reviews
| (1 Rating, 0 Reviews) |
Average Rating:
|
|
Events and News
Track Dog Racing FAQ
Supercharger FAQ
Supercharger Belt Chart
Intercooler FAQ
Technical Articles
Supercharger Upgrade Checklist
Roll Bar FAQ
Dyno Runs
High Performance Radiators
Customer Testimonials
|
|